Detailed Guide to Fix Linksys Velop Red Light Issue

September 30, 2022 Harry Baker

Are you seeing a continuous flash of red from your Linksys Velop device? Is your device slower now due to this? If you answered yes to both of these questions, you will be relieved to hear that we know how to help you fix the problem. If you’re seeing a red light on your Linksys Velop, read on to learn about the various troubleshooting tips to resolve the Linksys Velop red light issue.

[Fixed] Linksys Velop Red Light Issue

1. Restart the Linksys Velop

The Linksys Velop red light issue may, in fact, be fixed in many different ways. It is advised that you consider rebooting your device before moving on to more sophisticated troubleshooting hacks. If the red light problem persists after you’ve rebooted your device, don’t let us stop you from trying the more complex solutions.
Here are the steps to power cycle your Linksys Velop:

  • It is recommended that you unplug your Velop from the wall socket.
  • Currently, you must wait.
  • Plug in the power cord and turn the device on

Does the Linksys Velop red light issue persist after a reboot? Don’t lose your mind just yet. The steps outlined below may still be of assistance.

2. Update the Firmware

You can also try to update the firmware by accessing the Linksys Velop login page to fix the Linksys Velop red light issue. Get your Velop device up-to-date by following these steps:

  • Using a cable, connect your range Velop to your primary network device.
  • Open a browser on your computer and perform Linksys Velop login.
  • You can do this using the admin login credentials of your device.
  • Settings may be accessed once the Linksys Velop setup dashboard appears.
  • The Firmware Update menu will be found in the Administration menu.
  • When you locate it, go ahead and click it.

Verify that the Linksys Velop red light issue no longer appears after upgrading the firmware on your device. Does it still exist? It seems you need to do some further reading.

3. Pull the WiFi Devices Closer

If your Linksys Velop is still blinking red, it may be because there is too much space between your devices. The modem and the Velop must be next to one another. The use of an Ethernet connection, as opposed to wireless connectivity, is also recommended.

4. Contact Your Internet Service Provider

If the LED light is still flashing red, your internet connection is probably moving at a glacial rate. Therefore, guarantee that your Linksys Velop device always has a stable connection. It’s probably best to contact your ISP just to be cautious. Assuming the problem originates with him, you should request that he take immediate action to resolve it.

5. Reconfigure Your Linksys Velop

In case you are still experiencing the Linksys Velop red light issue, it is probably because you did not do Linksys Velop setup properly. To fix the issue, you should try setting up your device right from scratch, like the very first time you set it up. You can do that using either the Manual method or the Linksys application.

After walking through all these troubleshooting hacks, it is recommended that you check again if the Linksys Velop red light issue has been fixed or not.

In the Nutshell

After you have finished the reset process, verify that the Linksys Velop red light issue Linksys Velop red light issue has been fixed on your Linksys Velop device. If it has happened, we would like to congratulate you. Contact our technical support team if you’re still going crazy over the same issue.

Even if you ping them in the middle of the night, they will be always there to help you out with your Linksys Velop-related issues. Thus, contact them now without wasting even a single more minute.


Disclaimer: is an information provider. It is not affiliated with any third-party brand or manufacturer. provides information on troubleshooting issues related to various extenders, routers and similar networking devices. Our services are provided only on demand to users.